Vertical GeoFlex – 1 meter
The GeoFlex system is a string of MEMS sensors, 1 meter apart, ideal for geotechnical monitoring applications including:
- Monitoring deformation of the diaphragm walls that support deep excavations.
- Monitoring ground movements induced by tunnel construction.
- Monitoring deformations of embankments and retaining walls.
- Monitoring landslide areas above dams, highways, and railroads to provide early warning of slope failure.
Request to Quote
| GEOFLEX SYSTEM CONFIGURATIONS | |
|---|---|
| Casing | Choose 70 mm or 85 mm diameter inclinometer casing. |
| GeoFlex Segments | Choose the number of GeoFlex segments required, and casing diameter. If mixing 1M and 0.5M length strings, order one additional adapter cable 57802201, for each transition where 0.5m strings are attached below 1 m strings. |
| Suspension Kit | Order one suspension kit for each installation. The kit includes the suspension gate and hardware for securing the system. |
| Signal Cable | Each borehole requires a bottom plug to seal the end of the signal cable and a jumper cable to connect to the datalogger. |
| Data Logger | Campbell Scientific: The GeoFlex system works with many Campbell Scientific dataloggers. The CR6 or CR1000Xe can log two GeoFlex systems per logger directly. The CR350 can log one GeoFlex system. |
| DGSI GTecLink Wireless Dataloggers | Use the GTecLink dataloggers for easy wireless data monitoring. The Digital Node works with up to 10 nodes, while the GeoFlex Node works with up to 50. |
| Data Reduction Software | Process the GeoFlex data with a spreadsheet or the Sensly web-based monitoring system. |
| GEOFLEX NODE SPECIFICATIONS | |
|---|---|
| Sensor Type | MEMS (Micro ElectroMechanical Systems) tilt sensor for inclination readings |
| Requirements | Minimum supply voltage of 10 Vdc. Maximum supply voltage of 30 Vdc. Digital RS485 signal requires Campbell Scientific or GTecLink datalogger |
| Calibrated Range | ±30 degrees from vertical over a temperature range of -10°C to +40°C |
| Resolution | 9 arc seconds or 0.04 mm/m |
| Repeatability | ±82 arc seconds or ±0.4 mm/m. Required Casing: Fits 70 mm or 85 mm diameter inclinometer casing |
| Required Casing | Fits 70 mm or 85 mm diameter inclinometer casing. |
| Waterproof | Waterproof to 2 MPa. Signal |
| Weight | 650 g per 1 meter segment |
- Real-Time Monitoring – The GeoFlex system is ideal for continuous, unattended monitoring and can deliver readings in near-real time.
- Signal Cable Installation – Each sensor connects to the previous sensor above, requiring only one signal cable for each string and making data logger wiring easy.
- Mix and Match Sensor Spacing – 1 m node spacing strings may be integrated with traditional 0.5 m node spacing strings for greater data resolution at targeted depths. GeoFlex systems are made easy to ship. The sections connect with quick release clevis pins and separate for shipping, so the segments can ship in a 1.2 meter long box. We include spare clevis pins with each segment. This makes the logistics of a GeoFlex installation easy. You can send the packages to a job site through overnight mail, carry a GeoFlex array in the trunk of your car, or even strap it to the cargo rack on an ATV and haul it to a remote job location. DGSI also offers sensor-less nodes to install at the top of the system, letting you save money by only monitoring the zone of interest and bypassing the upper layers.
- Durable Components – Nodes, cables, connectors and gage rods are exceptionally durable, making it practical to remove the systems at the end of the project and redeploy them on other projects.
- Data Reduction – The GeoFlex system outputs the displacement as engineering units, requiring less computing power and a lighter load on your data acquisition system. No need to keep track of what node has what calibration coefficients or what order you installed the segments in the datalogger detects and configures this automatically.
- Complete Solution – DGSI offers complete monitoring solutions that
include dataloggers and web-based monitoring software that can check for
alarm conditions in near-real time and can plot data immediately after retrieving the readings.
The system can contain up to 150 sensor nodes in a vertical string installed in 85 mm or up to 50 nodes in a 70 mm inclinometer casing. The casing provides access for subsurface measurements. The joints between each sensor are robust, allowing the system to maintain a consistent orientation of all the nodes. The casing is typically installed in a vertical borehole that passes through a suspected zone of movement. The nodes are spaced at 1 meter to provide cost effective monitoring. The system spans the zone of movement and when the ground moves, the casing moves with it, changing the inclination of the nodes inside. Cumulating the deflections along the string produces a graph of the casing profile. Changes indicate displacement (movement). The GeoFlex system uses a data acquisition system, and can transmit
readings to cloud-based processing software that can trigger alarms based on displacements or rate of change.








