Embedment Strain Gauge

VW Embedment Strain Gauge

 

Applications

Durham Geo's VW embedment strain gauge is used to measure strain in reinforced concrete and mass concrete.
 

Operation

The embedment strain gauge operates on the principle that a tensioned wire, when plucked, vibrates at a frequency that is proportional to the strain in the wire. The gauge is constructed so that a wire is held in tension between two end flanges. Loading of the concrete structure changes the distance between the two flanges and results in a change in the tension of the wire. An electromagnet is used to pluck the wire and measure the frequency of vibration. Strain is then calculated by applying calibration factors to the frequency measurement.
 

Installation

In reinforced or pre-stressed concrete applications, the embedment strain gauge is usually tied to the reinforcing cage. In mass concrete applications, the gauge may be installed either before or immediately after placement of the concrete. Gauges may be configured in a rosette either by direct placement in the soft concrete or by attachment to a rosette adapter.

Embedment Strain Gauge

Advantages

Permanently Attached Coils: The coils used to excite and read the vibrating wire cannot be accidentally separated from the body during installation and wiring operations.

Built-in Temperature Sensor: The temperature sensor is useful for temperature corrections when the gauge is installed on materials that have a different temperature coefficient.

Reliable Signal Transmission: The arc-weldable strain gauge provides a strong signal which can be transmitted reliably over long distances with properly shielded cable.
 

For more information

Please download the datasheet and manual for the VW Embedment Strain Gauge. These documents can be viewed and printed with Adobe Acrobat Reader.

VW Embedment Strain Gauge drawing

VW Embedment Strain Gauge Specifications

EMBEDMENT STRAIN GAUGE
VW Embedment Strain Gauge 52650226 Vibrating wire strain gauge for monitoring strain in reinforced or mass concrete. Includes a built-in thermistor. Signal cable not included
Range 3,000 microstrain, set mid-range
Resolution 1 microstrain with VW Indicator
Accuracy ± 0.5% FS
Thermal Coefficient 12 ppm /°C
Length 168 mm ( 6.625" )
PICKUP AND SIGNAL CABLE
VW Standard Clip-On Pickup 52641110 Standard clip-on pickup includes 10 feet (3m) of signal cable and a hose clamp
VW Custom Length Clip-On Pickup 52641100 Custom clip-on pickup includes the pickup and a hose clamp. Signal cable must be ordered separately and will be installed at the factory
Signal Cable 50613824 Shielded cable with four 22-gauge tinned-copper conductors and flexible poly-vinyl chloride (PVC) jacket rated to 80°C(176°F)
TERMINAL BOXES
Terminal Box for 6 sensors 57711606 Provides terminals for signal cable from 6, 12, or 24 sensors. Sensors are selected by rotary switch. Dimensions of 6-sensor box are 240 x 190 x 120 mm (9.5 x 7.5 x 4.75"). Dimensions of 12 and 24-sensor boxes are 290 x 345 x 135 mm (11.5 x 13.5 x 5.25")
Terminal Box for 12 Sensors 57711600
Terminal Box for 24 Sensors 97711624
Universal Connector 57705001 For terminating a single cable. Connector not required when sensors are connected to a terminal box, a data logger, or to the terminal posts on the VW Data Recorder
READOUT
VW Data Recorder 52613500 The VW Data Recorder displays VW sensor readings in Hz or H2 /1000 and thermistor data in degrees C. It can also record the readings. See separate datasheet.
Jumper Cable for Terminal Box. 52613557 The jumper cable is required when the VW Data Recorder is to be connected to a terminal box or to a connector attached to signal cable
DATA LOGGERS
VW MiniLogger 52613310 The VW MiniLogger is a compact, low-cost data logger for one sensor. See separate datasheet
4-Channel V-Logger 52615140
8-Channel V-Logger 52615180
Campbell Scientific Data Loggers Campbell data loggers with a VW interface and the AM16/32 multiplexer can accommodate 16 sensors with temperature readings or 32 sensors without without temperature readings